A pair of stainless steel foot components complete with a standard threaded tie-down system.

Includes:

• 2 foot components
• 2 socket screws
• 1 Standard threaded tie-down system (shown below)

Standard threaded tie-down system as used on both our Standard and Aluminium Armatures.

Includes:

• 1 Tie-down rod
• 1 Wing nut

Beautifully made aluminium hip block. Used in our Aluminium Armatures.

Includes:

• 1 Hip block
• 3 socket screws

Precision made aluminium shoulder block. Used for our Aluminium Armatures.

Includes:

• 1 Shoulder block
• 3 socket screws

220mm 1/4 inch (6.35mm) K&S aluminium tubing.

Includes:

• 1 x 220m length of tubing

2mm aluminium wire. This wire is specifically for animation, it is malleable as well as long lasting especially when used with protective heat shrink tubing.

Includes:

• 15 metres of 2mm wire

1mm aluminium wire. This wire is ideal for making any of our armature's hands. It is specifically for animation, is malleable and long lasting (Particularly when used with protective heat shrink tubing).

Includes:

• 45 metres of 1mm wire

Heat shrink tubing makes animation wire more durable, helping it last longer. It simply slides over the wire and then when heated shrinks to by as much as half it's original size, down to 1.25mm. Used on our armature's hands.

Includes:

• 1 metre of 2.5mm heat shrink tubing

Perfected for protecting bundles of twisted aluminium animation wire, making it more durable. This tubing shrinks by up to half it's size when heated, shrinking to 2.5mm. Used on our Aluminium Armatures.

Includes:

• 1 metre of 5mm heat shrink tubing

Not used for any of our armatures, but ideal for protecting large bundles of twisted aluminium animation wire. It shrinks down to 5mm.

Includes:

• 1 metre of 10mm heat shrink tubing

Ball joint made from stainless steel with two pivot points. The balls are 8mm with an M4 threaded hole.

Includes:

• 2 Threaded balls
• 1 Standard plate
• 1 Threaded plate
• 1 Slotted screw

Stainless steel ball joint with one pivot point. The balls are 8mm and have an M4 threaded hole.

Includes:

• 1 Threaded ball
• 1 Fixing ball
• 1 Fixing component
• 1 Standard plate
• 1 Threaded plate
• 1 slotted screw

Stainless steel threaded balls as used in our Standard Armatures. These balls have an M4 threaded hole and are sold in batches of 10.

Includes:

• 10 Threaded balls

These balls have a threaded through hole and are used in our Standard Armature's fixed joints. They can also be used to make ball joints, but their motion isn't as smooth as that of our threaded balls.

Includes:

• 10 Fixing balls

Brass component used in the fixed joints of our Standard Armatures.

Includes:

• 1 Fixing component

Precision made stainless steel foot components complete with a standard threaded tie-down rod.

Includes:

• 2 Foot components
• 1 Standard threaded tie-down system (shown below)

Standard threaded tie-down system as used on both our Standard and Aluminium Armatures.

Includes:

• 1 Tie-down rod
• 1 Wing nut

Made from brass and featuring two through threaded holes. Used to make the "T" and "X" section on the Standard Armature.

Includes:

• 1 Universal joint

175mm stainless steel M4 threaded rod

Includes:

• 1 Threaded rod

The hands on our armatures have been designed to be easily replaced. It is a good idea to have spares ready for when they eventually wear out.

Includes:

• 3 Metres 1mm wire
• 1 Metre 2.5mm heat shrink
• 2 Finger plates
• 2 Square brass tubes

This ball joint is made from stainless steel and is used in both our Professional and ProPlus armatures. It has two pivot points. The balls are 6mm with an M3 threaded hole.

Includes:

• 2 Threaded balls
• 1 Threaded plate
• 1 Countersunk plate
• 1 C/S screw

As used in our Professional and ProPlus armatures, these fixed joints have one pivot point. The balls are 6mm with an M3 threaded hole.

Includes:

• 1 Threaded balls
• 1 Fixing component
• 1 Threaded plate
• 1 Countersunk plate
• 1 C/S screw

Stainless steel threaded balls which are used in our Professional and ProPlus Armatures. These balls have an M3 threaded hole and are sold in batches of 10.

Includes:

• 10 Threaded balls

These components are made from stainless steel and are used in our fixed joints. They have an M3 threaded hole.

Includes:

• 1 Fixing component

Made from stainless steel and includes two through M3 threaded holes. Used to make the "T" and "X" section on the Professional Armature.

Includes:

• 1 Universal joint

An excellent component allowing for the addition of rigging to your armature. The rigging block includes 4 M4 threaded holes into which out riggin system can be attached. Comes as standard on our ProPlus armatures.

Includes:

• 1 Rigging block

Precision made stainless steel foot components complete with threaded tie-down rod.

Includes:

• 2 Foot components
• 1 Standard threaded tie-down system (shown below)

Standard threaded tie-down system as used on both our Professional and ProPlus Armatures.

Includes:

• 1 Tie-down rod
• 1 Wing nut

175mm stainless steel M3 threaded rod

Includes:

• 1 Threaded rod

The hands on our armatures have been designed to be easily replaced. These wire hands are used on our Standard and Professional Armatures but also compatible with our ProPlus Armatures too although you would need some additional tubing, available below.

Includes:

• 3 Metres 1mm wire
• 1 Metre 2.5mm heat shrink
• 2 Finger plates
• 2 Square brass tubes

Four pieces of square brass tubing, which are cut to size. Used for attaching wire hands to our ProPlus Armatures.

Includes:

• 2 lengths of 20mm long tubing
• 2 lengths of 5mm long tubing

The ProPlus hands are exceptional quality combining the armature's hand and fingers with a ball jointed wrist joint. The fingers simply screw into place allowing for them to be easily replaced.

Includes:

• 2 Hand components
• 2 Threaded balls
• 2 Patched setscrews
• 6 M2 machine screws
• 3 Metres 1mm wire
• 1 Metre 2.5mm heat shrink
• 1 Allan key

0.7mm aluminium wire. The wire is specifically for animation, and heat shrink tubing allows maximum durability. These items are used in our ProPlus hands.

Includes:

• 3 metres of 0.7mm wire
• 1 metre of 2.5mm Heat Shrink

An excellent component allowing for the addition of rigging to your armature. The rigging block includes 4 M4 threaded holes into which out riggin system can be attached. Comes as standard on our ProPlus armatures.

Includes:

• 1 Rigging block

This precision made ball joint offers strength as well as smooth motion. Designed for our rigging system it can also be used for custom made armatures.

Includes:

• 2, 8mm threaded balls
• 1 threaded plate
• 1 countersunk plate
• 1 socket cap screw